Aluminum Sheet 3003 with PVC Film for Curtain Wall

Model NO.: 3003
Shape: Flat
Trademark: Baodi
Specification: SGS, ROHS
Origin: China
HS Code: 760612
Model NO.: 3003
Shape: Flat
Trademark: Baodi
Specification: SGS, ROHS
Origin: China
HS Code: 760612
Alloy: 3003
H14, H24, O. H112
Thickness: 0.1-150mm
We offer aluminum sheet, thick plate, aluminum coil, aluminum checkered plate, aluminum tube etc.

3003 chemical composition

Aluminum Balance

Copper 0.05 - 0.2

Iron 0.7 max

Manganese 1 - 1.5

Remainder Each 0.05 max

Remainder Total 0.15 max

Silicon 0.6 max

Zinc 0.1 max

AL 3003 is an alloy with very good corrosion resistance and moderate strength. It is not heat treatable and develops strengthening from cold working only.

Commonly used in chemical equipment, ductwork, and in general sheet metal work. 3003 is also used in the manufacture of cooking utensils, pressure vessels, builder's hardware, eyelet stock, ice cube trays, garage doors, awning slats, refrigerator panels, gas lines, gasoline tanks, heat exchangers, drawn and spun parts, and storage tanks.

We could supply aluminum sheet 3003 according to customer' dimension and quantity.

Surface: Mill finished, anodized, embossed

Specification Name: 3000 series aluminum sheet
Alloy: 3003, 3004, 3005, 3105 etc.
Temper: O, H12, H22, H32, H14, H24, H26, H18 etc.
Thickness: 0.25-200mm
Width: Up to 1800mm
Length: Up to 6000mm
Surface treatment: mill finished, anodized, embossed, PVC coated
Feature Machinability: It is readily machined and is considered as having good machinability for the aluminum alloys,.
Forming: It is readily formed by either conventional cold working or hot working.
Welding: It is readily accomplished by means of conventional welding methods.
Heat Treatment: It is a non-heat treatable alloy.
Forging: It may be hot forged in the range of 950 F to 500 F.
Hot Working: The hot working range (as for forging) is 950 F to 500 F. In that range the alloy is easily hot worked.
Cold Working: It is readily cold worked by all conventional methods.
Annealing: Annealing, during or following cold working, is done at 775 F, allowing adequate time for thorough heating, followed by air cooling.
Hardening: Hardens as a result of cold working only.
Application Chemical equipment, ductwork, and in general sheet metal work, cooking utensils, pressure vessels, builder's hardware, eyelet stock, ice cube trays, garage doors, awning slats, refrigerator panels, gas lines, gasoline tanks, heat exchangers, drawn and spun parts, and storage tanks etc.
Alloy Chemical Component %≤
Si Fe Cu Mn Mg Cr Ni Zn Ti others Al
single total
3003 0.6 0.7 0.05-0.20 1.0-1.5 \ \ \ 0.1 \ 0.05 0.15 remainder
3004 0.3 0.7 0.25 1.0-1.5 0.8-1.3 \ \ 0.25 \ 0.05 0.15 remainder
3005 0.6 0.7 0.3 1.0-1.5 0.2-0.6 0.1 \ 0.25 0.1 0.05 0.15 remainder
3105 0.6 0.7 0.3 0.3-0.8 0.2-0.8 0.2 \ 0.4 0.1 0.05 0.15 remainder
Contact Ms. Cherry Xia   Mobile:86-15106464366

Alloy: 3003
H14, H24, O. H112
Thickness: 0.1-150mm
We offer aluminum sheet, thick plate, aluminum coil, aluminum checkered plate, aluminum tube etc.

3003 chemical composition

Aluminum Balance

Copper 0.05 - 0.2

Iron 0.7 max

Manganese 1 - 1.5

Remainder Each 0.05 max

Remainder Total 0.15 max

Silicon 0.6 max

Zinc 0.1 max

AL 3003 is an alloy with very good corrosion resistance and moderate strength. It is not heat treatable and develops strengthening from cold working only.

Commonly used in chemical equipment, ductwork, and in general sheet metal work. 3003 is also used in the manufacture of cooking utensils, pressure vessels, builder's hardware, eyelet stock, ice cube trays, garage doors, awning slats, refrigerator panels, gas lines, gasoline tanks, heat exchangers, drawn and spun parts, and storage tanks.

We could supply aluminum sheet 3003 according to customer' dimension and quantity.

Surface: Mill finished, anodized, embossed

Specification Name: 3000 series aluminum sheet
Alloy: 3003, 3004, 3005, 3105 etc.
Temper: O, H12, H22, H32, H14, H24, H26, H18 etc.
Thickness: 0.25-200mm
Width: Up to 1800mm
Length: Up to 6000mm
Surface treatment: mill finished, anodized, embossed, PVC coated
Feature Machinability: It is readily machined and is considered as having good machinability for the aluminum alloys,.
Forming: It is readily formed by either conventional cold working or hot working.
Welding: It is readily accomplished by means of conventional welding methods.
Heat Treatment: It is a non-heat treatable alloy.
Forging: It may be hot forged in the range of 950 F to 500 F.
Hot Working: The hot working range (as for forging) is 950 F to 500 F. In that range the alloy is easily hot worked.
Cold Working: It is readily cold worked by all conventional methods.
Annealing: Annealing, during or following cold working, is done at 775 F, allowing adequate time for thorough heating, followed by air cooling.
Hardening: Hardens as a result of cold working only.
Application Chemical equipment, ductwork, and in general sheet metal work, cooking utensils, pressure vessels, builder's hardware, eyelet stock, ice cube trays, garage doors, awning slats, refrigerator panels, gas lines, gasoline tanks, heat exchangers, drawn and spun parts, and storage tanks etc.
Alloy Chemical Component %≤
Si Fe Cu Mn Mg Cr Ni Zn Ti others Al
single total
3003 0.6 0.7 0.05-0.20 1.0-1.5 \ \ \ 0.1 \ 0.05 0.15 remainder
3004 0.3 0.7 0.25 1.0-1.5 0.8-1.3 \ \ 0.25 \ 0.05 0.15 remainder
3005 0.6 0.7 0.3 1.0-1.5 0.2-0.6 0.1 \ 0.25 0.1 0.05 0.15 remainder
3105 0.6 0.7 0.3 0.3-0.8 0.2-0.8 0.2 \ 0.4 0.1 0.05 0.15 remainder
Contact Ms. Cherry Xia   Mobile:86-15106464366

Center Valve

Center Valve,Rotation Type Center Valve,Sanitary Center Valve,Beer Racking Arm Valve

Ningbo Wenhan Fluid Equipments Co., Ltd. , https://www.wenhanvalves.com