Heating cover construction and acceptance
Entrance decoration restaurant decoration heating paint decoration design window space
Ultra Plantâ„¢ Grow Light offers One Chip Technology aimed to meet your indoor growing expectation such as improve plants' quality, increase yield, or better the margin, etc., all for helping you realize a higher return on your crops.
From Ultra Plantâ„¢ APP, you are able to schedule the growing process including photoperiod, brightness and spectral in advance. The lighting system will help you grow smarter, easier and better.
Grow Light On Hemp,Hemp Grow Lights,Hemp Led Grow Lights,Best Grow Light On Hemp Feton Corporation , https://www.ultraplantleds.com
2. Heating hood construction specification
(1) Stationary heating cover: Before installation, the wall and floor shall be used to ensure the position of the heating cover. The length of the heating cover shall be 100 mm longer than the heat dissipation fins. The height shall be below the window sill or level with the window sill. Should be more than 10 mm wider than the heating, radiator cover area should account for more than 80% of the heat sink area. In the wall surface and floor installation line, drill the lower wooden mold, and the mold should be treated with anti-corrosion. According to the size of the mounting line, the skeleton of the dragon is made and the skeleton of the wooden dragon is fixed on the wall and the ground with a round nail. The distance from the wall surface is less than 200 mm and the distance from the ground is less than 150 mm. The round nail should be nailed to the wooden mold. The frame of the heat shield should be planed and flat. The heating cover side panel can use pentalithic panels. The top should increase the suspension lining, trim panel with triple plastic sheet. Before the panel is installed, the latex should be brushed on the outside of the heating hood frame. After the facing panel is fixed on the wooden keel with the shooting nail, the panel should leave the position of the radiator cover, and the edge is flush with the frame. The top and sides of the front are covered with wood lines. Make a cooling cover frame, the frame should be planed, flat, size should be consistent with the frame on the keel, the side of the pressure line closed mouth, the frame can be modeled.
(2) The movable heating cover: Because it is easy to move, it can be used for maintenance work. The width is narrower than the fixed heating cover and it takes up less space. Therefore, it is more appropriate to install the heating cover alone on the wall instead of other Siamese furniture. When used. The movable heating cover shall be regarded as a furniture production. According to the length, width and height of the heat sink, the cover has a side plate and a heat-dissipating net on three sides, with a length of more than 100 mm, a height of more than 50 mm and a width of more than 15 mm. In the box, mount the cover directly on the heat sink.
3. Construction Caps for the Heating Hood The construction of the heating hood shall be started after the indoor ceiling and the wall have been treated by the grassroots level, and the basement wall shall be leveled. The wooden aggregates and decorative materials produced by the heating cover shall meet the standards of fine wood decoration, the materials shall have no defects, the moisture content shall be less than 10%, and the moisture content of the plywood shall be less than 8%. The keel should use red and pine wood. The skeleton of the heating cover must be opened, and the plum eye should be glued to the stick. The extrusion must be tight and the connection must be firm. The veneer should be processed to the correct size, the surface is smooth and smooth, the lines are smooth, the fitting is tight, there is no obvious stick, hanging glue, exposed nail cap and pollution and other defects. After the production of the heating cover woodwork is completed, the finish treatment shall be immediately carried out, and after the clean oil is applied again, other operations may be performed.
4. Acceptance of the heating cover The specification, size and shape of the heating cover meet the design requirements. When the heating cover is used alone, the surface corners are rounded, and the scattered leakage network is in line with the frame of the heating cover. It can be installed and disassembled freely. The heating cover should be natural and divided. The roof structure of the heating cover is firm, and the wood keel and veneer panel ~ goods f white comply with the fine woodworking production material standards. The quality of the wooden surface brushing is in accordance with the requirement of fine carpentry production.
5. Common problems in the construction of heating enclosures and their handling The common quality problems in the construction of heating enclosures are mainly reflected in two aspects. In terms of structural design, the main quality issues are the small heat dissipation surface, no heat flow through the circuit, and the lack of heat dissipation during use and the veneer material's tendency to deform. When the heating cover is set for juice, there should be enough space for heat dissipation, and ventilation holes should be designed at the bottom of the heating cover to form a loop of air in the cover to accelerate the heat dissipation of the heat sink. The common quality problem in construction production is that the specification deviation exceeds the production standard. The manufacturing standards for the heating cover are as follows: The height difference between the two ends of the heating cover is less than 1mm, the deviation of the surface flatness is less than 1mm, the deviation of the verticality is less than 2mm, and the deviation of the straightness of the upper mouth is less than 2mm. Can be adjusted by adjusting the skeleton of the dragon. Heating cover finish quality problem and its treatment method see the quality inspection part of the paint project construction.
6. Estimated duration of construction of the heating enclosure Construction and installation of the heating enclosure is a relatively technical project. The duration of the construction of the heating enclosure starts from the completion of the top and bottom wall foundations, and finishes the final varnish painting before the completion of the project. For example, there are 7 heating hoods in the three bedrooms and two halls. The carpentry production takes 5 days. The painter varies according to the type of paint used and the construction method. Generally, it can be used in conjunction with other wood finishing oils in 3 to 8 days. The rest is waiting time.
Ultra Plantâ„¢ Grow Light is combined our advanced All-In-One technology with patented optical design and customized light full spectrum supported from our experienced LED engineers, plant specialists and other partners working on horticulture.
Ultra Plantâ„¢ is the most versatile horticultural grow lighting fixture for indoor plants with flexible full spectrum, brightness control and uniform, wider light distribution, suitable for top lighting of all types of crops. No matter it applies to anywhere for any crop, Ultra Plantâ„¢ can do perfect work for you.