Old bathroom renovation renovation process matters needing attention

Every household needs a bathroom and it is used many times. Therefore, the degree of depletion of the bathroom is the highest, like second-hand housing or old-fashioned housing, many owners will carry out the second transformation of the bathroom , then the old bathroom renovation need to pay attention to what? Next, let's take a look at it.

Old bathroom renovation - considerations

1. The old bathroom renovation skills focus on the choice of materials

Since it is the transformation of the old bathroom, then the face is to remove the old materials, re-select the materials, in fact, this is a waste. As we all know, the bathroom is the longest contact with water sources, but also the home is the most easily wet site, so basically when doing the floor, the lower layer will be laid waterproof layer, the owner in the re-laying floor tiles, there is no need to remove the original waterproof layer, It can be reinforced on the basis of the original waterproof layer, which will make the waterproofing more firm. When choosing the materials, we should try our best to choose materials that are compatible with the original materials to facilitate the construction and matching.

2. The old bathroom renovation skills pay attention to the design of the ceiling

The ceiling of the bathroom affects the entire bathroom environment and more attention should be paid to the renovation of the old bathroom. General bathroom ceiling should be based on different types of specific design, such as the relatively large family bathroom, in the design to the top should fully consider the height of the bathroom, otherwise it would appear empty and empty the entire bathroom. There is no need to add individual factors in the design of washing or bathtubs to fill the space and make the bathroom more full and full. Of course, the ceiling material is better than the kitchen, because the wet environment of the bathroom play makes the ceiling quality is not very good corrosion, causing unnecessary trouble. And the ceiling is generally replaced with the general meeting, otherwise it will not appear with the match, so at the beginning of the selection we must consider the wet environment.

3. The old bathroom renovation skills focus on the choice of sanitary ware

Modern family bathrooms generally combine toilets and bathrooms so that sanitary ware is basically divided into bidets, toilets, and basins. The choice of sanitary ware is the most important consideration is its drainage capacity, especially the best choice for toilets with mute and water-saving features. Basin is divided into basin and pedestal, the function is basically the same, but the form is different, this will take into account the overall design of the old bathroom renovation, a larger bathroom is more suitable to choose a luxurious basin, if the best choice for future space-saving Pedestal basin.

4. The floor decoration materials for the bathroom are preferably made of anti-slip tiles with a raised pattern. This type of floor tile not only has good waterproof performance, but it is not too slippery even in the case of water; top: tide, cover most important. Pay attention to the prevention of water vapor, so it is better to use PVC buckle board with good waterproof performance; circuit: bathroom is relatively humid, so be extra careful when you install lights, wires; lamps and switches are best to use with security protection; And the plug can not be exposed.

5. If there is an old man in the home to use the toilet renovation , emergency alarm devices should be installed, in advance should be set up spare pipelines; the ground is not slipping even if the slipping of the ground material, and should consider the convenience of cleaning; set handrails, please Pay attention to the positional relationship between the armrests and the paper holders; install the easy-to-use toilets, flush switches, etc., in a place that is easy to operate.

What should pay attention to when renovating the old bathroom?

On the wall, about 30 cm of waterproof coating should be made to prevent water from soaking in the wall; if the wall of the bathroom is a non-load-bearing light wall, the entire wall should be painted with waterproof paint; if your home uses two If you use a bathtub, the height of the waterproof coating should be higher than the upper edge of the bathtub.

The wall tiles should be covered to resist the erosion of moisture and protect the waterproof layer of the walls. At the same time, it is easy to maintain cleanliness and beauty. The families who use the ceiling should pay attention to the parts covered by the ceiling and also be covered with tiles in order to protect them well. The entire wall.

After chiseling the original floor tiles, cement mortar must be used to level the floor and then waterproof. This will prevent leakage of the waterproof coating due to uneven thickness. The seams should be brushed into place. The seams between the bathroom wall and the seams between the upper and lower water pipes and the ground are the most prone to problems.

During the construction, we must urge the workers to handle the corners and put them in place. After the second renovation of the bathroom is completed, we will block all the ports of the toilet and build a 25 cm high “can” at the entrance. Pour 20 centimeters of water into the bathroom. After 24 hours, you will check whether there is any leakage around the wall and floor to ensure the quality of the bathroom waterproofing project.

Summary: The above detailed introduction of the old bathroom renovation materials and construction need to pay attention to the place, I hope to be helpful to everyone.

Bathroom Remodeling Toilet Decoration Reminder Bathroom Renovation Old House Toilet Remodeling 1.5 square meters Toilet Renovation

Pins

Brass fasteners are used for their physical and aesthetic properties. Brass is utilized due to its high thermal conductivity and corrosion resistant properties, it is suitable for use in hot and cold environments, and resistant to water corrosion, making it a staple of industries such as heating and plumbing. Brass fasteners are largely non-magnetic (like any fastener, slight magnetic properties can develop during the manufacturing process) and resistant to tarnishing.

Brass fasteners are suited for some marine environments, including brackish water and slow current sea water; brass in this environment develops a protective green coating. Brass fasteners are also commonly used with wood applications, as the golden coloring blends well with the tan wood. Brass is a softer metal and must be used with care, always drilling pilot holes and using driver bits that fit the head of the screw precisely to prevent stripping. Brass Bolts also require a pilot hole be driven before installtion.


Metal Pins,Stainless Steel Pins,Flange Alignment Pin,Safety Coupler Pin

Taizhou Hongchuang Hardware Co., Ltd. , https://www.taizhouhongchuang.com