The toilet installation has learned 10 steps step by step startling

The toilet is the center of the bathroom. If the toilet is not installed properly, it will leak from the bathroom and smell. In the general home decoration, the toilet installation is naturally given to the workers. However, if the workers are doing well, they have to watch for themselves. Learning some of the basics of installing a toilet is also beneficial for overseeing oneself. Today Xiao Bian took everyone to look at the toilet installation of the 10 steps should pay attention to what details!

1, inspection pipeline

Before installation, the master will conduct a comprehensive inspection of the sewage pipeline to see if there is mud and sand, waste paper and other debris plugged in the pipeline. At the same time, check whether the floor of the toilet installation level is horizontal. If the ground is found to be uneven, the floor should be installed when installing the toilet. Leveling. Saw the outlet short and allow the outlet to be as high as 2mm-5mm above the ground as far as conditions permit.

2, determine the pit distance

Before choosing the toilet, first determine the size of your house water, what is the distance from the water outlet to the wall? (The standard is only 300, 400 mm two).

3, choose the toilet

Then choose your favorite style according to the size, pay attention to choose the water-saving type (3-6 liters), order to see the model, origin, and now the products are mixed, shop around is no regrets choice.

4, check the receipt

Toilet before installation to determine whether your choice of products, accessories, instructions are complete, take a closer look at the instructions, understand some of the product issues, in order to prevent pilferage, cutting corners, remember.

5, handle the bottom of the toilet

The water outlet requires the installer to handle the leveling. The bottom of the toilet shall be installed with a special flange for the toilet, or the glass glue shall be applied evenly with the water outlet. The toilet shall be glued at the bottom and around, and the gap between the toilet and the wall shall be even, and the position shall be correct. smooth.

6, check the water level, waterway

After the toilet is in place, the water inlet is required to have no leakage, the water level is correct, the flushing is smooth, the switch is flexible, and the cover is stable.

7, block the reserved hole

Now install the toilet seat generally do not install the foot screw, but use glass glue to plug the reserved hole in the toilet to prevent turning.

8, install the anchor screw

If the anchor bolt is installed, use a special sealant installed on the toilet to apply evenly to the outer periphery of the toilet drain outlet at 2CM. The toilet's drain should face the center of the drainage pipe and draw the toilet around. The side of the expansion bolt position, take the toilet, drilling, bulging bulge, it should be noted that this new hole in the hole bulge buried in the hole, it is possible to break the waterproof layer, it is recommended that while embedding the expansion screw, Gush sealant around the hole, and then bury the bolt. Tighten the bulge first, let the expansion bolt fully open, strengthen its tension, and then screw the upper screw out and place the toilet directly. Tighten screws and caps to keep the overall appearance. At the meeting place between the toilet bowl and the ground surface, because the toilet bowl is not integrated with the ground surface, it can be stirred with a sealant and a transparent sealant to seal the outer mouth of the toilet bowl and allow it to maintain its integrity with the ground surface. Part of the toilet water can be blocked at the periphery of the toilet.

9, fixed toilet

After the toilet is installed, the glass glue (putty ash) or cement mortar must be allowed to put in water after curing. The curing time is generally 24 hours. If you ask an unprofessional person to install it, usually to save time, the construction staff will use cement as the adhesive directly. This is definitely not enough to fill the fixed position of the bottom of the toilet. In fact, there is a drawback in the middle. The cement itself has expansive properties and takes a long time. This method may lead to cracking of the base of the toilet bowl and it is not easy to maintain.

10. Install or debug tank accessories.

First check the water pipe, discharge the water for 3-5 minutes to flush the pipe to ensure the cleanness of the water pipe; install the angle valve and connecting hose, then connect the hose to the inlet valve of the installed tank fitting and press the water source to check the water supply. Whether the valve inlet and seal are normal, check whether the installation position of the drainage valve is flexible and whether there is any jamming or leakage, and check whether there is any leakage inlet valve filter device.

Editor's summary: The water seal in the toilet shall ensure the isolation of the pipeline. When the installation is completed, the outlet of the sewage pipeline and the toilet must be well sealed, otherwise it will return to the odor. The above is the point of toilet installation. I hope to help everyone.

Sanitary ware purchase decoration materials knowledge bathroom decoration toilet cement glass switch toilet waterproof bathroom size overall bathroom

137cm Wallcloth Wallfabric

China leading manufacturers and suppliers of Vinyl Wall Fabric :

Wallpaper Material: Vinyl/pvc surface with fabric/textile fabric backed

Wallpaper Size: 1.1m-1.37m*10m-50m

Wallpaper Style: 3D, Damask, Classic, Modern, Flowers, Bricks and Stone Wallfabric etc.

137Cm Wallcloth Wallfabric,Home Decor Wallpaper,Plain Design Wallcloth,Hotel Wall Cloth

SHAOXING VIGOUR DECORATION MATERIAL CO.,LTD , https://www.vigourwallpaper.com