The use of heating device rolling bearing is more labor-saving

Home>Bearing knowledge>Selecting heating device for rolling bearings is more labor-saving
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

The use of heating device rolling bearing is more labor-saving

Source: China Bearing Network Time: 2018-03-09

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
When the inner diameter of the bearing is greater than 70mm; or the cooperation interference is large; the bearing hole is swollen; this device saves labor and time; also prevents damage caused by excessive force.
At this time, the demand is to control the heating temperature; usually the bearing is heated to 80 ° C; up to 100 ° C. It is enough. Exceeding 120 °C will lead to the appearance of bearing tempering; resulting in a decrease in the hardness and accuracy of the ferrule.
First, the commonly used heating methods are:
1, electric heating plate heating method:
Place the bearing on a hot plate with a temperature of 100 °C for a few minutes; this method is the most succinct; if it is turned over several times, the bearing can be heated evenly; and the power is also high; the large-capacity bearing can use this method.
2, electric furnace heating method:
The bearing is placed in a closed active temperature control electric furnace for heating; uniform heating; precise temperature control; fast heating; suitable for a batch of heating many bearings.
3. Induction heating method:
The induction heater can quickly, securely and cleanly heat the bearing to the required temperature; this is uniquely suited to the case where the inner ring is tightly co-operated; because only the inner ring is heated; the outer ring is less heated; Easy to install on the shaft; also easy to fit into the seat hole.
4, bulb heating method:
Use a 50W bulb to heat the bearing; ensure that the heating temperature is around 100 °C; smaller bearings can be placed directly on the bulb; larger bearings can be placed in the cone of the bulb; the cone prevents heat loss from the bulb; Uniform heating. The cone cover can be adjusted up and down; in a certain scale, it can be used to heat the bearings of different sizes. If you choose a far-infrared bulb; pay attention to the direction of the bulb should be downward; avoid infrared rays is not conducive to human eyes. Imported pump A kind of bulb can save energy. The bulb heating method is suitable for occasions where the quantity is small and not often needed to heat the bearing; the ordinary bulb can also be used for lighting; in addition, no other equipment is required.
5, oil tank heating method:
This is a widely used traditional heating method; the oil trough is provided with a metal mesh at a distance of 50 to 70 mm from the bottom; the bearing is placed on the net; the large bearing is to be hung with a hook. The bearing should not be placed directly on the bottom of the groove; Part of the heat is too high; or the dirt deposited at the bottom of the tank enters the bearing. The key points of the oil tank heating method are as follows; mineral oil with good non-corrosive thermal stability should be used; the best is transformer oil; oil and container should be kept clean. The capacity of the oil tank should be determined by the size of the heated bearing and the amount of oil; if it is too containerized, the 诹 魇 魇 灰 灰 灰 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢 湃胫岢
Second, the key to the heating device method:
1 The heating temperature should be handled properly; if the temperature is too high, the bearing will be damaged; if the temperature is too low, the ferrule will be inflated in a large amount; the effect is not obvious. The heating temperature of 80~1000 °C will produce a large amount of thermal expansion of the inner ring inner diameter; For bearings with normal interference; it is already enough.
2 arrive at the required heating temperature; it is necessary to carry out the device as soon as possible; avoid the cooling and the device is difficult.
3 The bearing is also shortened in the width direction when cooling; therefore, the device must apply a certain pressure to press the inner ring to the shoulder; and after cooling, test with a very thin feeler gauge; can the inner ring end face and the shaft There is a gap between the shoulders. Totally; the butterfly is demanding, agile and precise.

Recommend to friends comments close window

Bearing related knowledge
The third generation of wheel bearing wheel bearing equipment, the use of knowledge plastics in the rolling bearing (3)
Common terms and definitions of rolling bearings (1)
Inch Tapered Roller Bearing LM501349/10


This article links to http://
Please indicate the bearing network http://

Previous: Bearing Professor summarizes the work of one-way bearing inspections. Next: What sliding bearing data can avoid smoothness?

The Interior Barn Door Hardware can save space and add some style by installing a barn door or two in your home. Maybe you have salvaged an old door from an actual barn, or purchased a prefabricated door, or even built your own. No matter the case, your door requires a unique set of hardware to properly install it, and many options are available in terms of style and appearance. We'll get you familiar with the Barn Door Hardware that you need.

A set of Interior barn door hardware kits,including 1 rail,2 hanger sets,5 stand-offs and screws,2 anti-jumpers,2 door stoppers ,1 floor guide and other accessories.

The Material is Carbon steel,they have different size such as 5ft,6ft,6.6ft,8ft etc.  

You can make any color you like,powder coating black,white,green,electroplating gold,antique brass and other customization.The loading weight Not more than 120kgs.

Interior Barn Door HardwareInterior Barn Door HardwareInterior Barn Door Hardware

Barn Door Hardware

Interior Barn Door Hardware,Barn Door Hardware,Bypass Barn Door Hardware,Sliding Barn Door Hardware,Barn Door Kit,Interior Barn Door Hardware Set

Foshan Nanhai Xin Jianwei Hardware Co., Ltd , https://www.aaghardware.com