Window soundproof sealing strip function window soundproof sealing strip precautions

The window is the most demanding place in the home decoration, then do you know about this window soundproofing seal ? Our decoration and decoration home network Xiaobian now tells friends what the role of the window soundproof sealing strip is. And how do you use this window insulation seal, and what are the precautions we need to know when using our window insulation seals.


窗户隔音密封条


First, the window sound insulation seal function


1. Sealing rubber strip plays an important role in waterproofing, sealing and energy saving in plastic steel doors and windows and broken aluminum doors and windows and wooden doors and windows, soundproof, dustproof, antifreeze and warm. It must have strong tensile strength, good elasticity, and better temperature resistance and aging resistance. In order to ensure the fastening of the strip and the profile, the cross-sectional structure of the strip must match the profile of the steel door and window. Sealing strips are generally used to open doors and windows, overhang windows, and fold doors and windows. The main functions are dustproof, insect proof, waterproof, soundproof, sealed and so on.


2. The installation position of the top is generally on the sliding window (door) fan, around the frame fan or on the sealing bridge (wind block), and the sealing between the frame and the fan is enhanced. The top specification is an important factor affecting the sliding door and window and watertight performance, and is also an important factor affecting the door and window switching force. If the top size is too large or the vertical hair is too high, not only the assembly is difficult, but also the resistance of the door and window is increased, especially the initial resistance at the time of opening and the final seating resistance at the time of closing. If the specification is too small, or the height of the vertical top is not enough, it is easy to get out of the slot, so that the sealing performance of the door and window is greatly reduced.


Second, the use of window insulation seals


1. There are many types of sealing strips. The range of different sealing strips is different. Therefore, when selecting the type of sealing strips, it must correspond to your own doors and windows, so that the doors and windows can be more tight. Pay attention when purchasing seals, choose non-toxic and tasteless environmental seals.


2, the top is generally installed around the door and window fan and the frame fan, the surface of the good quality top is not straight, the vertical hair is smooth and uniform, and no lint. The specifications of the sealing strip should be matched. If it is too small, the sealing strip will fall off, which will affect the tightness of the glass and the fan. If it is too large to assemble, it will make the movement resistance of the door and window larger, which will cause inconvenience.


3. There are special sealing strips on the doors and windows and the beading. When installing the sealing strip, the notch debris should be carefully removed to ensure uniform gap on both sides. The mounting part must be flat, not stretched, not curled, and the joint should be Less than 1MM.


窗户隔音密封条


Third, the window sound insulation seal notes


1. When the glass is installed, the debris in the notch is not removed in time, so that the glass and the notch are not aligned.


2. The gap between the glass and the glass slot is uneven. The rubber strip is in poor contact with the glass and the glass slot. The glass slot is protruded, and the sealing strip can be easily pulled off by hand.


3. The rubber strip is not broken at the corner, and it is not glued.


The measures for rectification are:


1. Before installing the glass, carefully remove the debris in the slot, such as mortar, brick scraps, wooden blocks, etc. When the glass is placed, it should be carefully centered to ensure uniform gap on both sides, and fixed in time to prevent collision displacement and deviation. The center of the slot.


2. The rubber sealing strip can not be pulled too tightly, and the length of the blanking is 20-30mm longer than the assembly length. It should be set in place during installation, the surface is straight, and it is in close contact with the glass and glass slot, so that the surrounding force of the glass is evenly distributed. At the corner, the rubber strip should be beveled off and glued firmly at the break.


3. When sealing the glass with sealant, the glass should be squeezed with rubber strips or rubber blocks to leave a gap of glue injection. The depth of glue injection should be no less than 5mm. Before the glue is cured, the glass should be kept from vibration.


The above is the introduction of some of the advantages and disadvantages of our window soundproof sealing strips, as well as some methods of using the window soundproof sealing strips, and the precautions for the window soundproof sealing strips, friends can also know, then everyone still wants to know The decoration information, you can come to pay attention to our decoration home network at any time.


More related wonderful reading:

What are the door and window curtain wall seals? Sealing strip fixed advantage

What is the role of steel window seals?

Plastic steel door and window seals common sense, plastic steel door and window seal manufacturers

How to replace the plastic window seal? Plastic steel window sealing installation matters

Door and window seals, steps for door and window seals

Pillow Blocks

Pillow block, also known as plumber block, which are bearing housings supplied without any bearings and are usually meant for higher load ratings and a separately installed bearing.

Pillow block or Plummer block housings can be used with high-capacity spherical roller bearings or self-aligning ball bearings. They are manufactured from high-strength cast iron as standard but are also available in cast steel or spheroidal graphite cast iron. The housings have a re-lubrication facility and can be used with either oil or grease lubrication.

PILLOW BLOCK

Pillow block or Plummer block can be 1 or 2- piece split types held together by two or four cap bolts. Most bases provide two or four mounting bolts. Most blocks are of Class 30 gray cast iron. For more strength and ductility, usually they can be furnished in ductile iron or cast steel.

We have specialized in producing US/EURO standard bearing housings more than 10 years, could help to design the bearing housing or produce the Bearing Housing according to your requirements. (OEM accepted)

Any questions, please feel free to contact with us!

If you are interested with our services or products, you are welcome to visit our factory at any time.

Pillow Blocks,Pillow Block Bearing,Pillow Block Bearing Types,Mounted Pillow Block

SHAOXING QIFENG AUTO PARTS CO., LTD. , https://www.sxqfap.com