Introduction knowledge and process flow of thin-walled seamless steel tubes
Brief introduction and knowledge of thin-walled seamless steel tubes Thin-walled seamless steel tubes are made by perforating steel ingots or solid tube blanks, which are then hot rolled, cold rolled or cold drawn. Thin-walled seamless steel tubes have an important position in China's steel tube industry. According to incomplete statistics, there are about 240 seamless tube production enterprises in China, and about 250 seamless steel tube units, with an annual production capacity of about 4.5 million tons. From the point of view, <φ76, accounting for 35%, <φ159-650, accounting for 25%. From the perspective of varieties, general-purpose pipes are 1.9 million tons, accounting for 54%; petroleum pipes are 760,000 tons, accounting for 5.7%; hydraulic props and precision pipes are 150,000 tons, accounting for 4.3%; stainless pipes, bearing pipes, and automobile pipes total 50,000 Ton, accounting for 1.4%. The purpose of door and window sealing strip Pvc Strip,Transparent Pvc Strip is divided into three categories: glass sealing strip (rubber strip), door leaf and door cover sealing strip and wool strip. The glass sealing strip is used for the sealing between glass and leaf and frame, the door leaf and door cover sealing strip is mainly used for the sealing between door panel and door frame, and the wool strip is mainly used for the sealing between frame and leaf. In the production and installation of plastic steel doors and windows, broken bridge aluminum doors and windows and wooden doors, sealing strip is an essential accessory. Transparent Pvc Strip,Pvc Strip,Aluminium Sliding Strip,Door And Window Sealing Strip GuangDong XinCheng Material CO.,LTD , https://www.xin-alu.com
The raw material of the thin-walled seamless steel tube is a round tube blank. The round tube blank is cut into a length of about 1 meter through a cutting machine, and is sent to a furnace for heating by a conveyor belt. The billets are heated in a furnace and the temperature is about 1200 degrees Celsius. The fuel is hydrogen or acetylene. Furnace temperature control is a key issue. After the tube blanks are released, they are put through the pressure puncher. The most common punching machine is a conical roller puncher. This puncher has high production efficiency, good product quality, large perforation diameter, and can wear a variety of steel types. After piercing, the round billet is successively rolled, rolled or extruded by three rolls. After squeezing, take off the sizing. The sizing machine drills through the cone at a high speed into the steel die to form a steel pipe. The inner diameter of the steel pipe is determined by the outer diameter length of the sizing machine drill. After the steel pipe is sizing, it enters the cooling tower and is cooled by spraying water. After the steel pipe is cooled, it must be straightened. After straightening the steel pipe, it is sent to the metal detector (or hydraulic pressure test) by the conveyor belt for internal inspection. If there are cracks inside the pipe, air bubbles and other problems will be detected. After the quality inspection of steel pipes, strict manual selection is also required. After the quality inspection of the steel pipe, the paint is sprayed with the serial number, specifications and production lot number. And lifted into the warehouse by a crane.
Specification: The specification of seamless steel pipe is expressed in outside diameter * wall thickness mm.
The sealant strip plays an important role in waterproof, sealing and energy saving in plastic steel doors and windows, bridge broken aluminum doors and windows and wooden doors and windows, with sound insulation, dust prevention, antifreeze and warmth preservation. It must have strong tensile strength, good elasticity, and good temperature resistance and aging resistance. In order to ensure the fastening of the rubber strip and the profile, the section structure size of the rubber strip must match the profile of plastic steel doors and windows. Sealant strips are generally used for flat doors and windows, suspended windows and folding doors and windows. The main functions are dust prevention, insect prevention, waterproof, sound insulation, sealing, etc.
The installation position of the wool top is generally on the sliding window (door) leaf, the circumference of the frame leaf or the sealing bridge (wind block) to enhance the sealing between the frame and the leaf. Top specification is an important factor affecting the and watertight performance of push-pull doors and windows, and it is also an important factor affecting the switching force of doors and windows. If the wool top specification is too large or the vertical wool is too high, it will not only make assembly difficult, but also increase the moving resistance of doors and windows, especially the initial resistance when opening and the final positioning resistance when closing. If the specification is too small, or the height of the vertical top is not enough, it is easy to fall out of the groove, which greatly reduces the sealing performance of doors and windows.
There are two kinds of tops: silicified and non silicified. The top after silicified treatment has better effect in use. The appearance of the top with qualified quality is that the surface is straight, the bottom plate and vertical hair are smooth and free of bending, and there are no pits on the bottom plate, which meets the requirements of 0.2mm.